IN-14 Arduino Shield NCS314 Nixie Clock with Columns and Arduino MEGA 2560. Arduino Shield Nixie Tubes Clock with Columns. Designed for 6 IN-14 xUSSR Nixie Tubes with Sockets. IN-14 Tubes are the most popular mass-produced Nixie Tubes.Nixie Clocks are one of the most beautiful and popular Vintage Clocks. Clock features Startup Tune, RGB backlight, USB port for updates.
Shield options include Tubes, Columns, Sockets and Power Supply. Sensor, GPS Receiver, IR Remote. Shield Clock is designed for Arduino UNO and MEGA 2560 Boards. It allows you to write your own uniqe programs for the Arduino platform. All the latest Source codes are always available on our GitHub channel.
PCB, Design, Schematics, Case and Software made by GRA & AFCH. Shield Tubes Clock (NCS314 Shield). IN-14 Nixie Tubes - 6 pcs Set. Columns with Dots - 2 pcs.
Arduino Control Board (MEGA 2560). User Manual on Vintage style paper. Columns with separating Dots are included for the Clock.
Arduino Control Board is included for the Clock. This listing does NOT contain the GPS, Remote and Power Supply. Pre-programmed Arduino Mega here: (Mega).
Beautiful Wooden case Case WCNS314. And upload software into your arduino. Github at the "NixeTubesShieldNCS314" repository. All our Nixie Tubes Clocks are using HV513WG chips, it provides higher brightness in multiplexing mode in comparison with HV5812 chip and greater reliability compared to legacy K155ID1. We offer flexible Tubes Boards platform, that support many Nixie Tubes (out Tubes Boards designed for IN-4, IN-8, IN-8-2, IN-12, IN-14, IN-16, IN-17, IN-18 and Z573, Z5660M, ZM1042, Z568M Nixie Tubes).
It is easy to build a beautiful Nixie Tubes Clock with our Boards, we also offer Acrylic, Wooden and Stone Cases for our Clocks. Fast uploading pf the Firmware via USB to the Control Board. All the latest version of the Firmwares to all our Nixie Clocks are always available on our GitHub channel. No need for additional drivers, we are using only genuine USB-to-serial converters (FTDI), drivers for them are pre-installed in all popular OSes: Windows, MacOS, Linux. It is easy to modify the Nixie Clock's Firmware functions for your tasks due to the open Arduino platform.
We use High Quality PCBs and Components, also we use Japanese aluminum capacitors only for our Boards (Nichicon, Panasonic). Tubes Board is easy to modify by cutting if you want to build 4 Tubes Clock [HH:MM] from 6 Tubes Clock. Our Nixie Boards use Power On Self-Test (POST): LED backlight flashing, Tubes flashing and Start up Tune.
Our Boards use, Firmware version can be seen at the end of the POST test. Our Tubes Boards use Unique detailed Tube test - our soft test checks each Tubes segment on every Tube so it distinguishable to see segments failures. If you have ANY questions. Shiled support 6 IN-14 Nixie tubes [hh:mm:ss].
Temperature display (DS18B20) [Celsius or Fahrenheit]. GPS time synchronization (requires a standard GPS receiver, NMEA protocol, 5 volt power supply, not included). Operation via IR remote control (Remote control Sony RM-X151, not included). No need refresh or update information on the tubes.
The maximum possible brightness of the tubes. Date format: DD:MM:YY. Unique RGB LEDs backlight with 16,7 million colors.
Very easy to switch LEDS off/on. As alarm sound clock uses standard RTTTL (Nokia format) melodies, so You can easy change it. (included songs: mission impossible, we wish you).Easy updating firmware via USB using Arduino IDE. Power On Self-Test (POST): LEDs test, tubes test, input voltage test, sound test. Integrated High Voltage Power supply: 150 - 220V. 3 PWM channels for RGB LEDs 8 bit per channel = 24bit = 16,7 million colors.
It can be disabled in the menu (see manual). Test points for testing, adjusting and controlling low and high voltage circuits. RTC (Real Time Clock) with Backup battery.3 buttons on board to control. Potenciometer to adjust High Voltage. IR reciver TSOP4836 for IR remote controllers (may conflict with "Tone" library).
8 pcs of RGB SMD LEDs. Places for 2 column with 2 neon dots inside.
Separate controls upper and lower dots. Recommended: 12V, 1-2A (center pin positive +).
Nixie Tubes Shiled NCS314 PCB size: 200mm x 53.34mm. (7.87 x 1.2 in). Arduino Nixie Tubes Clock Shield NCS314. Example of IN-14 Arduino Shield NCS314 with Columns and Arduino UNO and box. Boards Dimensions in 2D and 3D.
Nixie Tubes Clock Shiled for Arduino NCS314. If you have ANY questions, PLEASE ASK us.This item is in the category "Home & Garden\Home Décor\Clocks\Alarm Clocks & Clock Radios". The seller is "gra_and_afch_2" and is located in this country: UA. This item can be shipped worldwide.